Replacing a laptop screen is often an easy DIY project, and can be done by anyone with basic computer skills. To do it yourself, you’ll need a few tools and some patience.
To begin, switch off your laptop and remove the battery. Then, use an opening tool to pry the screen away from the laptop’s back cover.
1. Remove the Battery
Before you begin the process of replacing your laptop screen, it is important to first remove the battery. This will ensure that you do not damage any of the components in your computer and also help ensure that your screen will be properly fitted.
To begin, flip the laptop over to expose the battery latch and remove the screw that secures the battery in place. This can be done with a simple plastic opening tool, or an X-Acto knife if you are comfortable using one.
Next, gently lift the front bezel off of the screen. This should not be too difficult and should not take a lot of force, however, if you find it is too difficult to remove, you may have missed a screw and need to go back and check for any.
You should see several rubber plugs around the edges of the lid, and a couple or four in the corners of the top screen. You should be able to pop these out with a sharp knife or tweezers, and then insert the new screen bezel into the frame.
Once you have the screen bezel removed, you will need to connect all of the connecting cables that are connected to the old screen and then reconnect the video cable. This is a delicate task, and you should be very careful not to break any of the wires or connectors.
Once you have completed this process, you will have a brand new replacement screen that should work perfectly. You can test this by powering the laptop on and seeing if it boots up properly and displays the startup screen. This will show you that your new screen is functioning correctly and that all the connections are correct.
2. Remove the Front Bezel
The screen is the main display component of a laptop. It is a flexible flat panel that consists of pixels (or dots) that can each change their color independently. The number of pixels in a laptop screen is usually measured as the resolution, which can be anything from 1920×1080 to 720p.
A broken laptop screen can be a frustrating problem to deal with, but it is not impossible to replace. Fortunately, replacing a laptop screen can be a relatively easy project for the do-it-yourselfer, and it is usually inexpensive to do so.
First, you’ll need to remove the front bezel from your laptop. The bezel protects the screen and provides access to its components. It also serves as a cover when the laptop is closed.
To begin, remove the four screws that secure the screen bezel to the LCD cover. Then, start at the inside top edge and gently pry the bezel away from the LCD Module.
Continue to work your way down the sides and towards the middle, separating the securing clips that hold it in place. If necessary, use a plastic pry to release the corners of the bezel.
Once the screen bezel is free, locate the screen brackets and unscrew them. These are metal brackets that hold the screen assembly together.
Before unscrewing the brackets, make sure that you put them in a spot where you won’t lose them when you’re finished.
Next, use a hobby knife or box cutter to remove the rubber screw covers that are located along the front bezel of the screen assembly. These cover the screws that hold the screen bezel in place, and sometimes hide some screws underneath.
3. Remove the Frame
To begin this repair, you’ll need to remove the frame from your laptop. This consists of the back case and the bezel that’s attached to it by plastic snaps. You’ll also need a screwdriver and a pair of tweezers.
Once you have the bezel removed, you’ll need to remove the screws that hold the screen to the back of the laptop. These are usually located near the hinges.
Next, you’ll need to disconnect the video cable from the back of the screen. Most laptops have this connector near the center of the screen. The part of the cable that runs across the screen is usually glued to the back of the screen with some adhesive, so be careful when you pull it away from the connector.
You’ll also need to remove any tape that’s holding the connector to the back of the screen. This will make it easier to replace the cable with a new one.
After you have removed the cables from the back of the screen, you can then begin to remove the LCD itself. Most laptops have the video connector near the center of the screen, but some have it in the bottom or even a corner.
If you’re replacing a LCD screen, the manufacturer often provides you with a replacement video cable that you can use instead of the one that came with your original screen. This will ensure that the connector fits correctly and that the new screen is connected to the laptop properly.
When reinstalling the new screen, you should make sure to line up the edges of the bezel and the screen as closely as possible. This will prevent any damage when you put the laptop back together.
4. Remove the Screen
When you need to replace the screen on your laptop, it’s important to do so as safely as possible. If you don’t follow the proper steps, you can damage your device and cause further problems. This is why, if possible, we suggest a macbook repair singapore area performed by a professional technician.
Before removing the screen, you should remove the battery and disconnect the video cable from the back of your screen. This is so that you don’t accidentally short out the video cable or damage it.
Then, remove the front bezel from your laptop using a thin, flat tool, such as a guitar pick or a flat-blade screwdriver. You may need to pry the bezel off of your laptop with some force, but this should not harm your screen or the case.
Once the bezel is removed, you should find the LCD tethered to a metal trim frame on either side of the screen. Use a screwdriver to remove the two screws that secure these frame pieces to the back screen case.
After removing these screws, tilt the screen so that you can access the hinges that hold it to the metal brackets on the sides. This allows you to remove the hinge holding screws without causing any damage to your screen or case.
Some newest laptops have no screws and attach the LCD panel to the lid with double-sided adhesive tape. To pull it, locate the ends of the tape – top or bottom, left and right, and slowly pull it.
Often, the video cable that connects the LCD to the video connector at the bottom of the laptop is also attached to the back of the screen with some tape. Disconnect this tape, and then carefully unplug the video cable from the back of your screen.
5. Reassemble
When replacing a laptop screen, it is important to be careful not to damage the hardware. To avoid this, you should refer to manufacturer documentation and use appropriate hand tools for case disassembly & component removal.
You should also note the cable and screw locations so you can reassemble your computer properly. This will prevent you from damaging components or putting them back in the wrong position.
The first step in reassembling your laptop is to remove the battery. It is usually located under the keyboard and is connected to a cable. Once the battery is removed, you can then start to reassemble your laptop.
Once the battery is removed, you should begin to take out all the parts that are attached to your motherboard. This includes the storage drive, RAM, and wireless card.
Next, you will need to disconnect the video connector and inverter wires. This can be done by pulling them off gently.
After these two steps are completed, you should be able to remove the laptop screen. Depending on the model of your laptop, this can be done using a pair of tweezers or a small screwdriver.
Alternatively, you can use a plastic putty knife to separate the bezel from the frame. However, if you have a problem with this step, you can always ask a professional to do it for you.
Once the laptop screen is detached, you will need to remove any hinge holding screws that are used to attach it to the case. These may be hidden under stickers or under the rubber feet.
